In-process out-of-roundness measurement probe for turned workpieces

S. Mekid; K. Vacharanukul

doi:10.1016/j.measurement.2011.01.011

In-process out-of-roundness measurement probe for turned workpieces

S. Mekid^*, K. Vacharanukul

^*Corresponding author for this work

Research output: Contribution to journal › Article › peer-review

51 Scopus citations

Abstract

A new in-process and non-contact probe is proposed to measure the diameter and the roundness of turned workpieces. The initial probe discussed in previous publications exhibited diameter measurements with good accuracy (uncertainty 5 μm over 100 mm). This paper discusses the implementation of roundness measurement into the initial probe and its performance. The principle of the roundness measurement is based on the relationship between the displacement and the light intensity. The probe delivers a maximum error of 0.5 μm with an uncertainty of 1 μm for roundness measurement over a range of 100 mm diameter.

Original language	English
Pages (from-to)	762-766
Number of pages	5
Journal	Measurement: Journal of the International Measurement Confederation
Volume	44
Issue number	4
DOIs	https://doi.org/10.1016/j.measurement.2011.01.011
State	Published - May 2011
Externally published	Yes

Keywords

Diameter measurement
Laser measurement
Non-contact measurement
Roundness measurement

ASJC Scopus subject areas

Instrumentation
Electrical and Electronic Engineering

Access to Document

10.1016/j.measurement.2011.01.011

Cite this

@article{1638e4326e124650a1fcc3102d0655d5,

title = "In-process out-of-roundness measurement probe for turned workpieces",

abstract = "A new in-process and non-contact probe is proposed to measure the diameter and the roundness of turned workpieces. The initial probe discussed in previous publications exhibited diameter measurements with good accuracy (uncertainty 5 μm over 100 mm). This paper discusses the implementation of roundness measurement into the initial probe and its performance. The principle of the roundness measurement is based on the relationship between the displacement and the light intensity. The probe delivers a maximum error of 0.5 μm with an uncertainty of 1 μm for roundness measurement over a range of 100 mm diameter.",

keywords = "Diameter measurement, Laser measurement, Non-contact measurement, Roundness measurement",

author = "S. Mekid and K. Vacharanukul",

year = "2011",

month = may,

doi = "10.1016/j.measurement.2011.01.011",

language = "English",

volume = "44",

pages = "762--766",

journal = "Measurement: Journal of the International Measurement Confederation",

issn = "0263-2241",

number = "4",

}

TY - JOUR

T1 - In-process out-of-roundness measurement probe for turned workpieces

AU - Mekid, S.

AU - Vacharanukul, K.

PY - 2011/5

Y1 - 2011/5

N2 - A new in-process and non-contact probe is proposed to measure the diameter and the roundness of turned workpieces. The initial probe discussed in previous publications exhibited diameter measurements with good accuracy (uncertainty 5 μm over 100 mm). This paper discusses the implementation of roundness measurement into the initial probe and its performance. The principle of the roundness measurement is based on the relationship between the displacement and the light intensity. The probe delivers a maximum error of 0.5 μm with an uncertainty of 1 μm for roundness measurement over a range of 100 mm diameter.

AB - A new in-process and non-contact probe is proposed to measure the diameter and the roundness of turned workpieces. The initial probe discussed in previous publications exhibited diameter measurements with good accuracy (uncertainty 5 μm over 100 mm). This paper discusses the implementation of roundness measurement into the initial probe and its performance. The principle of the roundness measurement is based on the relationship between the displacement and the light intensity. The probe delivers a maximum error of 0.5 μm with an uncertainty of 1 μm for roundness measurement over a range of 100 mm diameter.

KW - Diameter measurement

KW - Laser measurement

KW - Non-contact measurement

KW - Roundness measurement

UR - https://www.scopus.com/pages/publications/79952191179

U2 - 10.1016/j.measurement.2011.01.011

DO - 10.1016/j.measurement.2011.01.011

M3 - Article

AN - SCOPUS:79952191179

SN - 0263-2241

VL - 44

SP - 762

EP - 766

JO - Measurement: Journal of the International Measurement Confederation

JF - Measurement: Journal of the International Measurement Confederation

IS - 4

ER -

In-process out-of-roundness measurement probe for turned workpieces

Abstract

Keywords

ASJC Scopus subject areas

Access to Document

Fingerprint

Cite this